Skip to content
Decking fasteners · Ground screws · Accessories info@fastshifter.com
Outdoor lighting · for the trade

Concrete-free foundations for garden lights

A ground-screw kit for garden bollards and pillar lights — for lighting brands, electrical and lighting wholesalers and installers. No digging out, no concrete, no curing: the light can be wired the same day.

Why installers like it

01

No concrete, no curing

Wind the screw in and fix the light. It can be wired and switched on the same day.

02

Cable inside the foundation

Openings in the screw let the supply cable run inside the foundation, out of sight and protected.

03

Lawns and planted beds

Goes in without digging up the planting or lifting turf around the light.

04

Level by winding

Wind the screw in or out until the plate sits level at the right height.

05

Removable

Lights can be moved later. There is no concrete to break out.

Fastshifter ground screw for outdoor lamp posts with 120 mm mounting plate
Item no. 240350K

What’s in the kit

Set 240350K has everything needed to set four garden lights. Once the luminaires are chosen, there is nothing else to buy.

  • 4 × ground screw 68 × 350 mm with 120 mm mounting plate and cable openings, electro-galvanised black
  • 1 × steel turning bar 14 × 430 mm, hot-dip galvanised, for driving the screws by hand
  • 28 × SS410 stainless self-tapping screws 4 × 30 mm, T15: 14 black + 14 silver, to match the lamp finish
  • 2 × metal drill bits 3 × 60 mm
  • 1 × T15 driver bit

Original Fastshifter design · Registered EU Design No. 015041720-0001

Does it fit your lights?

Most small garden bollards and pillar lights fix with three bolts on a bolt circle of roughly 60–100 mm. The holes are drilled on site into the 120 mm plate (drill bits are in the kit), so one foundation suits many fittings.

It is made for garden-scale lights. It is not intended for commercial bollards with large base plates, or for posts taller than about 1 m.

It works with 12 V and 230 V fittings: the foundation is passive steel. Wiring must follow local rules and be done by a qualified electrician where required.

Not sure about a fitting? Add its base dimensions to your sample request.

Who we work with on this product

01

Lighting brands & importers

Add the Fastshifter kit as an accessory to your garden lights: one foundation that suits many of your fittings.

02

Electrical & lighting wholesalers

A ready-made foundation kit for the installers who already buy garden lighting from you.

03

Landscaping & garden-construction suppliers

For landscapers who set path and bed lighting alongside paving and planting.

04

Outdoor-lighting webshops

A practical add-on to a garden light, with product data and photos ready to list.

Install in 4 steps

  1. Mark & feed the cable

    Mark the light position and bring the supply cable to it.

  2. Wind it in

    Drive the screw in by hand with the turning bar, with the cable running inside the foundation.

  3. Level the plate

    Wind in or out until the plate is level, just above the finished ground.

  4. Drill & fix the light

    Drill the light’s fixing holes into the plate and fix it with the self-tapping screws.

Questions from the lighting trade

Will it fit our fittings?

Most small garden bollards and pillar lights with three bolts on a bolt circle of about 60–100 mm fit: the holes are drilled on site into the 120 mm plate. It is not meant for commercial bollards with large base plates or posts taller than about 1 m.

Does it work with 12 V and 230 V lights?

Yes. The foundation is passive steel and the cable runs inside it. Wiring must follow local rules and be done by a qualified electrician where required.

How do we get trade prices?

Prices are not published on the website. Ask for the price list with the form below and we will send it for your market.

Can we test it first?

Yes. Tick “Please send me product samples” in the form and we will arrange a sample kit, so you can try it with your own fittings.

Outdoor lighting

Request a sample kit or the price list

Tell us about your company and your lighting range. It takes two minutes.

info@fastshifter.com

Products of interest